(If this step is missed, then OBD software is not going to work. So it's CRUCIAL that you follow below steps).
Download the following ELM327 drivers: Driver Pack 1, Driver Pack 2
ELM327 devices plugs into the diagnostics socket in the car ang gives your phone access to car diagnostics. Recommended adapters brands: Kiwi 3, Viecar, V-Gate, Carista, LELink, Veepeak. Free map drawing software for mac. If you buy one of the cheap china OBD2 ELM327 adapters from ebay / amazon, then make sure it’s not marked as v.2.
Install.
That's it.
Dec 12, 2016 OBD Auto Doctor is the advanced OBD-2 software for Windows, Mac and Linux. The software enables you to communicate with your vehicle's On-Board Diagnostic system and turn your computer into a. OBD-II ScanMaster lies within System Utilities, more precisely Device Assistants. The latest version of the program can be installed on PCs running Windows XP/Vista/7/8/10, 32-bit. The actual developer of the free program is WGSoft. ELM327-USB-FT232RL-V1.4: Windows Drivers for ELM327-USB-FT232RL-V1.4 For ELM327 Scanners with FTDI FT232RL Serial USB Chip: Link 1: For Windows XP/7/8.1/10 (32/64 bit) ELM327-USB-FT232RL-V1.5: ELM327-USB-CP2102-V1.5A: Windows Drivers for ELM327-USB-CP2102-V1.5A For ELM327 Scanners with Silicon Labs CP2102 Serial USB Chip. ScanMaster-ELM is a OBD-2/EOBD diagnostic scan tool for vehicle diagnostics under OBD-II/EOBD standards that were developed specifically for the ELM327 chip from the company ELM Electronics. Does cleaning software make macs slow version. Operation system: Windows 2000, XP, 2003, Vista, Windows7, 8, 8.1 (32 and 64bit).
OBD-2 software will now detect your ELM327 cable — and connect to car also. (If cable is still not found, then install Driver Pack 3.)
1. Locate OBD 2 connector.
Plug your OBD 2 Bluetooth hardware interface into OBD 2 port ensuring a solid connection. OBD 2 connector locations vary by vehicle make. Please refer to service manual to locate your vehicle's OBD 2 port.
2. Turn the car ignition switch to ON.
Turn the car ignition on. If this is the first attempt the BLUETOOTH DEVICE MUST BE PAIRED.
3. Pairing Bluetooth interface.
(NOTE: You only have 60 seconds to pair the Bluetooth scanner from the time you connect it to the car — to the time of entering the Pairing code. If more then 60 second pass — then Pairing code will be rejected and you'll have to plug out the scanner and try again. So have your Bluetooth devices window open, so you can immediately connect as soon as you see ELM327/OBDII/Unknown Device show up.)
In the upper right of the Apple menu bar click the Bluetooth symbol. Scroll down to set up Bluetooth device (You may need to turn Bluetooth 'On' first).
4. Bluetooth Setup Assistant.
The Bluetooth setup assistant will search for devices automatically. The Bluetooth name for the ELM327 interfaces will be either 'OBDII' or 'CBT'. Or even different.
If your device does not appear, ensure the ignition is 'on' and your Bluetooth OBD 2 interface is securely connected. Verify that the OBD 2 interface is powered which is indicated by a steady red LED on the device.
5. Passcode Settings.Best Elm327 Software
After initially attempting to pair, the Bluetooth Setup Assistant should display the message, 'The pairing attempt was unsuccessful'. This indicates the pairing passcode needs to be set.
Click 'Passcode Options..' in the lower left.
Obd 2 Elm327 Software Mac Torrent6. Selecting a Passcode.
Select 'Use a specific passcode' and enter '6789'. If that doesn't work, then enter '1234'. If that doesn't work, then enter '0000'. Graphic tablet software mac free.
Click OK.
If the interface paired properly, a Bluetooth Setup Assistant window will appear confirming, 'Pairing was completed successfully' and 'A computer serial port was created'.
Click Quit.
(Note: If the message 'A computer serial port was created' does not appear, the interface IS NOT paired properly and OBD-2 software will not connect to your vehicle.)
7. You Are Ready To Connect!
Launch the OBD software. And click connect.
If it doesn't connect, then you'll need to configure software preferences and specify which port number your ELM Bluetooth is on.
This section addresses common connection preferences you'll find in typical OBD software. So this is a short guide in case you're stuck on what settings to adjust.
1. What should I select for Serial Port settings?
If the software has 'Auto' option to detect your ELM327 automatically — then choose it because it'll cycle through all ports on your computer until it finds the port with ELM327 connection on it.
However if it doesn't find your ELM327 interface, then you'll need to set the Serial/COM port manually to the same number where ELM327 is connected.
Typical example of OBD connection preferences. 2. What should the Port Speed (bps) be set at?
The interfaces we currently ship require the 38400 (bps) setting.
3. What is Parity and what should Parity be set to?
Parity is a method for error detection in transmission. For most interfaces Parity should be set to 'No Parity'.
4. What is the 'Timeout (sec)' for?
The timeout is how long the software will wait before it gives up on hearing back from a serial port.
Some cars respond more quickly, in which case the timeout should be set for a shorter duration so time is not wasted when troubleshooting connection issues.
However, some cars respond more slowly, in which timeout should be set for a longer duration to ensure that OBD software does not prematurely terminate communication.
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
December 2020
Categories |